manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 316 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 316

Driving your vehicle

106

5

Smart Cruise Control (SCC)

NOTICE

At a stop, if there is vehicle in front of 
your vehicle, Smart Cruise Control will 
turn on when the brake pedal is 
depressed.

Overtaking Acceleration Assist

Overtaking Acceleration Assist will oper

-

ate when the turn signal indicator is 
turned on to the left while Smart Cruise 
Control is operating, and the following 
conditions are satisfied:
僅 Your vehicle speed is above 60 km/h 

(40 mph)

僅 The hazard warning flasher is off
僅 A vehicle is detected in front of your 

vehicle

僅 Deceleration is not needed to main

-

tain distance with the vehicle in front

WARNING

僅 When the turn signal indicator is 

turned on to the left while there is a 
vehicle ahead, the vehicle may accel

-

erate temporarily. Pay attention to the 
road conditions at all times.

僅 Regardless of your country's driving 

direction, Overtaking Acceleration 
Assist will operate when the condi

-

tions are satisfied. When using the 
function in countries with different 
driving direction, always check the 
road conditions at all times.

Basic function

Operating

Temporarily canceled

You can see the status of the Smart 
Cruise Control operation in the Driving 
Assist view on the cluster. Refer to 
"Instrument cluster" on page 4-51.
Smart Cruise Control will be displayed as 
below depending on the status of the 
function.
僅 When operating
(1) Whether there is a vehicle ahead and 
the selected distance level
(2) Set speed
(3) Whether there is a vehicle ahead and 
the target vehicle distance
僅 When temporarily canceled

OBD051408N

OBD051409N

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments