manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 197 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 197

121

4

4

Features of your vehicle

Interior features

僅 To reduce the risk of personal injury in 

the event of sudden stop or collision, 
do not place uncovered or unsecured 
bottles, glasses, cans, etc., in the cup 
holder while the vehicle is in motion.

WARNING

Keep cans or bottles out of direct sun 
light and do not put them in a vehicle 
that is heated up. It may explode.

NOTICE

僅 Keep your drinks sealed while driving 

to prevent spilling your drink. If liquid 
spills, it may get into the vehicle's 
electrical/electronic system and dam

-

age electrical/ electronic parts.

僅 When cleaning spilled liquids, do not 

dry the cup holder at high tempera

-

ture. This may damage the cup 
holder.

Seat warmer (if equipped)

The seat warmer is provided to warm 
the front seats during cold weather.

Front seat

Rear seat

With the ignition switch or ENGINE 
START/STOP button in the ON position:
僅 Push either of the buttons to warm 

the driver's seat or the front passen

-

ger's seat.

During mild weather or under conditions 
where the operation of the seat warmer 
is not needed, keep the levers/switch in 
the "OFF" position.

Temperature control (Manual)

僅 Each time you press the button, the 

temperature setting of the seat will 
change as follows:

Front seat

Rear seat

僅 The seat warmer defaults to the OFF 

position whenever the ignition switch 
or ENGINE START/STOP button is 
turned on.

OBDM041023L

OBD041024N

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments