manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 186 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 186

Features of your vehicle

110

4

Automatic climate control system

Type B

僅 Type A
The outlet vents can be opened or 
closed separately using the thumbwheel. 
To close the vent, rotate it downward to 
the maximum position.Also, you can 
adjust the direction of air delivery from 
these vents using the vent control lever 
as shown.
僅 Type B
The outlet vents can be opened or 
closed separately turning the knob right 
or left. Also, you can adjust the direction 
of air delivery from these vents moving 
the knob freely to any directions.

Temperature control

The temperature will increase to the 
maximum (HI) by rotating the knob 
clockwise direction.
The temperature will decrease to the 
minimum (Lo) by rotating the knob anti 
clock wise direction.
When rotating the knob, the tempera

-

ture will increase or decrease by 0.5℃ (1

℉). When set to the lowest temperature 

setting, the air conditioning will operate 
continuously.

Adjusting the driver and passen

-

ger side temperature equally

1. Press the “SYNC” button to adjust the 

driver and passenger side tempera

-

ture equally.

OBD041308L

OBD041309L

OBD041333L

OBD041317L

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments