Kia FORTE 2022 Manual Download Page 170

Page: 170 / 514

Features of your vehicle

Interior lights

This vehicle is equipped with lights
throughout the vehicle to illuminate the
interior.

CAUTION

Do not use the interior lights for
extended periods when the engine is not
running.
It may cause battery discharge.

WARNING

Do not use the interior lights when driv

ing in the dark. Accidents could happen
because the view may be obscured by
interior lights.

Map lamp

Type A

Type B

僅 Press the lens (1) to turn ON the map

lamp.
To turn the map lamp OFF press the
lens (1) again.

僅

(2): DOOR mode

- The map lamp and room lamp

come on when a door is opened.
The lamps go out after approxi

mately 30 seconds.

- The map lamp and room lamp

come on for approximately 30 sec

onds when doors are unlocked with
a smart key as long as the doors
are not opened.

- The map lamp and room lamp will

stay on for approximately 10 min

utes if a door is opened with the
ignition switch or the ENGINE
START/STOP button in the ACC or
OFF position.

- The map lamp and room lamp will

stay on continuously if the door is
opened with the ignition switch or
the ENGINE START/STOP button in
the ON position.

- The map lamp and room lamp will

go out immediately if the ignition
switch or the ENGINE START/STOP
button is changed to the ON posi

tion or all doors are locked.

OBD041403L

OBD041058L

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Search results

Summary of Contents for FORTE 2022

Reviews:

Kia FORTE 2022, Manual, Page: 170 / 514

Search results

Summary of Contents for FORTE 2022

Reviews: