manualshive.com logo in svg

Kia FORTE 2022, Manual, Page: 113 / 514

Share
Download
Kia FORTE 2022 Manual Download Page 113

37

4

4

Features of your vehicle

Fuel filler door

causing a total loss of visibility, which 
might result in an accident.

WARNING

The support rod must be inserted com

-

pletely into the hole whenever you 
inspect the engine compartment. This 
will prevent the hood from falling and 
possibly injuring you.

Fuel filler door

Opening the fuel filler door

The fuel-filler door must be opened from 
inside the vehicle by pulling up on the 
fuel-filler door opener located on the 
front floor area on the driver's seat.
If the fuel filler door does not open 
because ice has formed around it, tap 
lightly or push on the door to break the 
ice and release the door. Do not pry on 
the door. If necessary, spray around the 
door with an approved de-icer fluid (do 
not use radiator anti-freeze) or move the 
vehicle to a warm place and allow the ice 
to melt.

1. Stop the engine.
2. To open the fuel filler door, pull up the 

fuel filler door opener.

OBD041541

OBD041429

Summary of Contents for FORTE 2022



































































































































































































































































































































































































































































































































Reviews:

No comments