manualshive.com logo in svg

Kia Cerato, Owner'S Manual, Page: 628 / 655

Share
Download
Kia Cerato Owner'S Manual Download Page 628

Maintenance

106

7

• Do not operate the engine in con-

fined or closed areas (such as
garages) any more than what is
necessary to move the vehicle in or
out of the area.

• When the vehicle is stopped in an

open area for more than a short
time with the engine running,
adjust the ventilation system (as
needed) to draw outside air into the
vehicle.

• Never sit in a parked or stopped

vehicle for any extended time with
the engine running.

• When the engine stalls or fails to

start, excessive attempts to restart
the engine may cause damage to
the emission control system.

Operating precautions for catalytic
converters (if equipped)

Your vehicle is equipped with a cat-
alytic converter emission control
device.
Therefore, the following precautions
must be observed:
• Use only UNLEADED FUEL for

petrol engines.

• Do not operate the vehicle when

there are signs of engine malfunc-
tion, such as misfire or a noticeable
loss of performance.

• Do not misuse or abuse the

engine. Examples of misuse are
coasting with the ignition off and
descending steep grades in gear
with the ignition off.

• Do not operate the engine at high

idle speed for extended periods (5
minutes or more).

• Do not modify or tamper with any

part of the engine or emission con-
trol system. All inspections and
adjustments must be made by an
authorised Kia dealer.

• Avoid driving with an extremely low

fuel level. Running out of fuel could
cause the engine to misfire, dam-
aging the catalytic converter.

WARNING

- Fire

• A hot exhaust system can

ignite flammable items under
your vehicle. Do not park the
vehicle over or near flamma-
ble objects, such as grass,
vegetation, paper, leaves, etc.

• The exhaust system and cat-

alytic system are very hot
whilst the engine is running or
immediately after the engine
is turned off. Keep away from
the exhaust system and cat-
alytic, you may get burned.
Also, do not remove the heat
sink around the exhaust sys-
tem, do not seal the bottom of
the vehicle or do not coat the
vehicle for corrosion control.
It may present a fire risk under
certain conditions.

Summary of Contents for Cerato
















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments