manualshive.com logo in svg

Kia Cerato, Owner'S Manual, Page: 485 / 655

Share
Download
Kia Cerato Owner'S Manual Download Page 485

5 89

Driving your vehicle

✽

✽

NOTICE 

- 

Location of trailer
mounting

The mounting hole for hitches are
located on both sides of the under-
body behind the rear tyres.

Hitches

It's important to have the correct hitch
equipment. Crosswinds, large trucks
going by, and rough roads are a few
reasons why you’ll need the right
hitch. Here are some rules to follow:
• Do you have to make any holes in

the body of your vehicle when you
install a trailer hitch? If you do, then
be sure to seal the holes later
when you remove the hitch.
If you do not seal them, deadly car-
bon monoxide (CO) from your
exhaust can get into your vehicle,
as well as dirt and water.

• The bumpers on your vehicle are

not intended for hitches. Do not
attach rental hitches or other
bumper-type hitches to them. Use
only a frame-mounted hitch that
does not attach to the bumper.

• Kia trailer hitch accessary is avail-

able at an authorised Kia dealer.

Safety chains 

You should always attach chains
between your vehicle and your trail-
er. Cross the safety chains under the
tongue of the trailer so that the
tongue will not drop to the road if it
becomes separated from the hitch.
Instructions about safety chains may
be provided by the hitch manufactur-
er or by the trailer manufacturer.
Follow the manufacturer’s recom-
mendation for attaching safety
chains. Always leave just enough
slack so you can turn with your trail-
er. And, never allow safety chains to
drag on the ground.

OYDEDI3080

OYD066012

• 4 Door

• 5 Door

Summary of Contents for Cerato
















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments