manualshive.com logo in svg

Kia Cerato, Owner'S Manual, Page: 48 / 655

Share
Download
Kia Cerato Owner'S Manual Download Page 48

Safety features of your vehicle

30

3

The seat belt pre-tensioner system
consists mainly of the following com-
ponents. Their locations are shown in
the illustration:
1. SRS air bag warning light
2. Front retractor pre-tensioner

assembly

3. SRS control module

✽

✽

NOTICE

• When the pre-tensioner seat belts

are activated, a loud noise may be
heard and fine dust, which may
appear to be smoke, may be visible
in the passenger compartment.
These are normal operating condi-
tions and are not hazardous.

• Although it is harmless, the fine

dust may cause skin irritation and
should not be breathed for pro-
longed periods. Wash all exposed
skin areas thoroughly after an acci-
dent in which the pre-tensioner seat
belts were activated.

✽

✽

NOTICE

Because the sensor that activates the
SRS air bag is connected with the
pre-tensioner seat belt, the SRS air
bag warning light (

) on the

instrument panel will illuminate for
approximately 6 seconds after the
ignition switch has been turned to
the ON position, and then it should
turn off.

WARNING

To obtain maximum benefit
from a pre-tensioner seat belt:
1. The seat belt must be worn

correctly and adjusted to the
proper position. Please read
and follow all of the important
information and precautions
about your vehicle’s occupant
safety features – including
seat belts and air bags – that
are provided in this manual.

2. Be sure you and your passen-

gers always wear seat belts
properly.

8KMB3311/H

Summary of Contents for Cerato
















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments