manualshive.com logo in svg

Kia Cerato 2022, Owner'S Manual, Page: 418 / 622

Share
Download
Kia Cerato 2022 Owner'S Manual Download Page 418

Driving your vehicle

144

6

Rear Cross-Traffic Collision-Avoidance Assist (RCCA)

appear on the cluster. At the same 
time, an audible warning will sound.

僅 The function will operate when the 

following conditions are satisfied:
- Your vehicle gear is shifted to R 

(Reverse)

- Your vehicle speed is below 8 km/h 

(5 mph)

- The approaching vehicle is within 

approximately 25 m (82 ft.) from 
the left and right side of your vehi

-

cle

- The speed of the vehicle approach

-

ing from the left and right is above 
5 km/h (3 mph)

NOTICE

If the operating conditions are satisfied, 
there will be a warning whenever the 
vehicle approaches from the left or right 
side even though your vehicle speed is 0 
km/h (0 mph).

Emergency Braking

僅 Your vehicle, the warning light on the 

side view mirror (outside mirror) will 
blink and a warning message will 
appear on the cluster. At the same 
time, an audible warning will sound.

僅 The function will operate when the 

following conditions are satisfied:
- Your vehicle gear is shifted to R 

(Reverse)

- Your vehicle speed is below 8 km/h 

(5 mph)

- The approaching vehicle is within 

approximately 1.5 m (5 ft.) from the 
left and right side of your vehicle

- The speed of the vehicle approach

-

ing from the left and right is above 
5 km/h (3 mph)

OBD051385L

OBD041246R

OBD041599R

Summary of Contents for Cerato 2022















































































































































































































































































































































































































































































































































































































































Reviews:

No comments