manualshive.com logo in svg

Kia Cerato 2022, Owner'S Manual, Page: 415 / 622

Share
Download
Kia Cerato 2022 Owner'S Manual Download Page 415

141

6

6

Driving your vehicle

Rear Cross-Traffic Collision-Avoidance Assist (RCCA)

Rear Cross-Traffic Collision-
Avoidance Assist (RCCA) (if 
equipped)

Rear Cross-Traffic Collision-Avoidance 
Assist is designed to detect vehicles 
approaching from the left and right side 
whilst your vehicle is reversing, and 
warning the driver that a collision is 
imminent with a warning message and 
an audible warning. Also, to help prevent 
collision braking assist is applied.

[A]: Rear Cross-Traffic Collision Warning 
operating range
[B]: Rear Cross-Traffic Collision-Avoid

-

ance Assist operating range

CAUTION

The time of warning may vary depend

-

ing on vehicle speed of the approaching 
vehicle.

NOTICE

In the following text, Rear Cross-Traffic 
Collision Warning and Rear Cross-Traffic 
Collision-Avoidance Assist will be 
referred as Rear Cross-Traffic Safety 
system.

Detecting sensor

[1]: Rear corner radar
Refer to the picture above for the 
detailed location of the detecting sensor.

CAUTION

For more details on the precautions of 
the rear corner radar, refer to "Blind-
Spot Collision-Avoidance Assist (BCA) (if 
equipped)" on page 6-94.

Rear Cross-Traffic Collision-
Avoidance Assist settings

Rear Cross-Traffic Safety

With the ignition switch or ENGINE 
START/STOP button in the ON position, 
select 'Driver assistance → Parking 
safety → Rear cross-traffic safety' from 

ODL3059072

OBD052376R

OBD041259R

Summary of Contents for Cerato 2022















































































































































































































































































































































































































































































































































































































































Reviews:

No comments