manualshive.com logo in svg

Kia Cerato 2022, Owner'S Manual, Page: 198 / 622

Share
Download
Kia Cerato 2022 Owner'S Manual Download Page 198

Features of your vehicle

114

4

Interior lights

Type B

僅 Press the lens (1) to turn ON the map 

lamp.
To turn the map lamp OFF press the 
lens (1) again.

僅

 (2): DOOR mode

- The map lamp and room lamp 

come on when a door is opened. 
The lamps go out after approxi

-

mately 30 seconds.

- The map lamp and room lamp 

come on for approximately 30 sec

-

onds when doors are unlocked with 
a smart key as long as the doors 
are not opened.

- The map lamp and room lamp will 

stay on for approximately 10 min

-

utes if a door is opened with the 
ignition switch or the ENGINE 
START/STOP Button in the ACC or 
OFF position.

- The map lamp and room lamp will 

stay on continuously if the door is 
opened with the ignition switch or 
the ENGINE START/STOP Button in 
the ON position.

- The map lamp and room lamp will 

go out immediately if the ignition 
switch or the ENGINE START/STOP 
Button is changed to the ON posi

-

tion or all doors are locked.

- To turn off the DOOR mode, press 

the DOOR button (2) once again 
(not pressed).

僅

 (3): Press this switch to turn the 

front map lamps on.

僅

 (4): Press this switch to turn the 

front map lamps off.

NOTICE

The DOOR mode and ROOM mode can 
not be selected at a time.

Room lamp

僅

 : The light stays on at all times.

Trunk/tailgate room lamp

The trunk/tailgate room lamp comes on 
when the trunk (tailgate) is opened.

OBD041058L

OSK3048007NR

OBD041420L

Summary of Contents for Cerato 2022















































































































































































































































































































































































































































































































































































































































Reviews:

No comments