Kia Cerato 2022 Owner'S Manual Download Page 177

Page: 177 / 622

Features of your vehicle

Reverse Parking Distance Warning (PDW)

Reverse Parking Distance
Warning (PDW) (if equipped)

Reverse Parking Distance Warning will
warn the driver if an obstacle is detected
when the vehicle is backing up at low
speeds.

Detecting sensor

Type A

Type B

[1] : Rear ultrasonic sensors
Refer to the picture above for the
detailed location of the detecting sen

sors.

WARNING

僅 Reverse Parking Distance Warning

may not operate normally when:
- Moisture is frozen on the sensor
- Sensor is covered with foreign mat

ters, such as snow or water

- Outside air temperature is

extremely hot or cold.

- Sensor components are arbitrarily

removed.

- The sensor is pushed, scratched or

stuck with any hard and sharp
objects that could damage the sur

face.

- High pressure water is directly

applied to ultrasonic sensor.

僅 Reverse Parking Distance Warning

may malfunction when:
- Driving on uneven road, gravel

roads or bushes

- Objects that generates ultrasonic

waves such as vehicle horns, loud
motorcycle engine sound or truck
air brakes are near the sensor

- Heavy rain or water spray is pres

ent

- Wireless transmitters or mobile

phones are present near the sensor

- The sensor is covered with snow
- Affected by another vehicle's sen

sors

- Water flows on the surface of the

sensor

- Installing the license plate differ

ently from the original location

- The vehicle bumper height or sen

sor installation has been modified.

- Any non-factory equipment or

accessories have been installed.

OBD042001R

OBD042415

Summary of Contents for Cerato 2022















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Cerato 2022

Reviews:

Kia Cerato 2022, Owner'S Manual, Page: 177 / 622

Search results

Summary of Contents for Cerato 2022

Reviews: