manualshive.com logo in svg

Kia Cerato 2022, Owner'S Manual, Page: 128 / 622

Share
Download
Kia Cerato 2022 Owner'S Manual Download Page 128

Features of your vehicle

44

4

Sunroof

僅 Regularly remove any accumulated 

dust on the sunroof rail.

僅 Dust accumulated between the sun

-

roof and roof panel can make noise.
Open the sunroof and remove dust 
regularly using a clean cloth.

僅 Do not try to open the sunroof when 

the temperature is below freezing or 
when the sunroof is covered with 
snow or ice. The sunroof may not 
work properly and may break if 
opened by force.

僅 Do not open or drive with the sunroof 

glass open immediately after rain or 
washing the vehicle. Water may wet 
the interior of the vehicle.

僅 Do not extend any luggage outside 

the sunroof whilst driving. Vehicle 
damage may occur if the vehicle sud

-

denly stops.

WARNING

Do not extend your head, arms, body 
parts or objects outside the sunroof 
whilst driving. Injuries may occur if the 
vehicle suddenly stops.

Resetting the sunroof

In some circumstances resetting the 
sunroof operation may need to be per

-

formed. Some instances where resetting 
the sunroof may be required include:
僅 When the 12-volt battery is either dis

-

connected or discharged

僅 When the sunroof fuse is replaced
僅 If the sunroof one-touch AUTO OPEN/

CLOSE operation is not functioning 
properly

Sunroof resetting procedure:
1. It is recommended to perform the 

reset procedure with the vehicle 
engine running. Start the vehicle in P 
(Park).

2. Make sure the sunroof glass is in the 

fully closed position. If the sunroof 
glass is open, push the switch forward 
until the sunroof glass is fully closed.

3. Release the switch when the sunroof 

glass is fully closed.

4. Push the switch forward until the sun

-

roof glass moves slightly. Then 
release the switch.

5. Once again push and hold the sun

-

roof switch forward until the sunroof 
glass slides open and close. Do not 
release the switch until the operation 
is completed.
If you release the switch during oper

-

ation, start the procedure again from 
step 2.

INFORMATION

If the sunroof does not reset when the 
vehicle battery is disconnected or dis

-

charged, or the sunroof fuse is blown, 
the sunroof may not operate normally.

OCD041538L

Summary of Contents for Cerato 2022















































































































































































































































































































































































































































































































































































































































Reviews:

No comments