Home
/
Kia
/
Cerato 2022
/
Owner'S Manual

Kia Cerato 2022, Owner'S Manual, Page: 123 / 622

Share

Page: 123 / 622

Kia Cerato 2022 Owner'S Manual Download Page 123

39

4

4

Features of your vehicle

Fuel filler door

Fuel filler door

Opening the fuel filler door

4 Door

5 Door

The fuel-filler door must be opened from
inside the vehicle by pulling up on the
fuel-filler door opener located on the
front floor area on the driver's seat.

NOTICE

If the fuel filler door does not open
because ice has formed around it, tap
lightly or push on the door to break the
ice and release the door. Do not pry on
the door. If necessary, spray around the
door with an approved de-icer fluid (do
not use radiator anti-freeze) or move the

vehicle to a warm place and allow the ice
to melt.

4 Door

5 Door

1. Stop the engine.
2. To open the fuel filler door, pull up the

fuel filler door opener.

3. Pull open the fuel filler door (1).
4. To remove the cap, turn the fuel filler

cap (2) counterclockwise.

5. Refuel as needed.

WARNING

Before refuelling, be sure to check what
type of fuel is used for your vehicle.
If you put diesel fuel into a petrol-pow

-

ered vehicle or petrol into a diesel-pow

-

OBD041050R

OBD041541R

OBD041052

OBD041429

«
...
121
122
123
124
125
...
»

Summary of Contents for Cerato 2022















































































































































































































































































































































































































































































































































































































































Reviews:

No comments