manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 93 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 93

3 83

Knowing your vehicle

Electric remote control 
(if equipped)

The electric remote control mirror
switch allows you to adjust the posi-
tion of the left and right outside
rearview mirrors. To adjust the posi-
tion of either mirror, move the lever
(1) to R or L to select the right side
mirror or the left side mirror, then
press a corresponding point (

▲

) on

the mirror adjustment control to posi-
tion the selected mirror up, down, left
or right.
After adjustment, put the lever into
neutral position to prevent the inad-
vertent adjustment.

Folding the outside rearview 
mirror

Manual type

To fold outside rearview mirror, grasp
the housing of mirror and then fold it
toward the rear of the vehicle.

OED036047R

CAUTION

• The mirrors stop moving when

they reach the maximum
adjusting angles,

but the

motor continues to operate
whilst the switch is
depressed. Do not depress
the switch longer than neces-
sary, the motor may be dam-
aged.

• Do not attempt to adjust the

outside rearview mirror by
hands. Doing so may damage
the parts.

1LDA2083A/H

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments