manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 48 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 48

Knowing your vehicle

38

3

Lap/shoulder belt

To fasten the front lap/shoulder
belt:

1. Grasp the buckle and tongue

plate.

2. Slowly pull the lap/shoulder belt

out from the retractor.

3. Insert the tongue plate (1) into the

open end of the buckle (2) until an
audible “click” is heard, indicating
the belt is locked in the buckle.

4. Position the lap portion (1) of the

belt across your lap as LOW ON
THE HIPS as possible to reduce
the risk of sliding under it during
an accident. Adjust the belt to a
SNUG FIT by pulling up on the
shoulder portion (2) of the seat
belt. The belt retractor is designed
to take up excess webbing auto-
matically and to maintain tension
on the belt. For your safety, do not
put any excess slack into the seat
belt at any location.

OMG035302

OMG035303

OMG035301

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments