manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 37 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 37

3 27

Knowing your vehicle

CAUTION  

• When returning the rear seat-

backs to the upright position,
remember to return the rear
shoulder belts to their proper
position.

• Do not remove the floor carpet

in your vehicle. Emission con-
trol system components
cause high exhaust tempera-
tures under the floor.

WARNING

- Cargo

Cargo should always be
secured to prevent it from being
thrown about the vehicle in a
collision and causing injury to
the vehicle occupants.

5. Pull the lock release lever (5).
6. Fold the seatback forward and

down firmly (6).

7. Put the headrest poles into the

holes on the rear of the seat cush-
ion (7).

To unfold the rear seat:

1. Remove the headrest.
2. Whilst slightly pushing the seat

cushion towards the front of the
vehicle, lift and push the seatback
backward firmly until it clicks into
place.

3. Place the headrest to the proper

position.

4. Move and push the seat cushion

downward firmly to the proper
position.

5. Check the rear seat belt and buck-

le.

OED036027

OED036028

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments