Kia Ceed 2006 Owner'S Manual Download Page 333

Page: 333 / 349

7 59

Maintenance

License plate lights bulb
replacement

1. Loosen the lens retaining screws

with a cross-tip screwdriver.

2. Remove the lens.
3. Remove the bulb by pulling it

straight out.

4. Install a new bulb.
5. Reinstall the lens securely with the

lens retaining screws.

(1) Rear fog light (if equipped)
(2) Rear turn signal light
(3) Back-up light
(4) Stop and tail light

Rear combination light bulb
replacement

1. Open the rear hatch.

2. Remove the service cover by turn-

ing the plastic screw counterclock-
wise and removing the cover.

OED076051

OED076053

OED076052

Summary of Contents for Ceed 2006






























































































































































































































































































































































Search results

Summary of Contents for Ceed 2006

Reviews:

Kia Ceed 2006, Owner'S Manual, Page: 333 / 349

Search results

Summary of Contents for Ceed 2006

Reviews: