manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 314 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 314

Maintenance

40

7

WIPER BLADES 

Wiper blade maintenance  

✽

✽

NOTICE

Commercial hot waxes applied by

automatic car washes have been

known to make the windscreen diffi-

cult to clean.  

Contamination of either the wind-
screen or the wiper blades with for-
eign matter can reduce the effective-
ness of the windscreen wipers.
Common sources of contamination
are insects, tree sap, and hot wax
treatments used by some commer-
cial car washes. If the blades are not
wiping properly, clean both the win-
dow and the blades with a good
cleaner or mild detergent, and rinse
thoroughly with clean water.

Windscreen wiper blade
replacement  

When the wipers no longer clean
adequately, the blades may be worn
or cracked, and require replacement.

1. Turn the ignition swich off and

remove the key.

2. Push the wiper lever downward to

the one touch wiper position for
more than 2 seconds, then the
wiper blades will stop upward
position. (if equipped)

CAUTION

To prevent damage to the wiper
blades, do not use petrol,
kerosene, paint thinner, or other
solvents on or near them.

CAUTION

To prevent damage to the wiper
arms or other components, do
not attempt to move the wipers
manually.

CAUTION

The use of a non-specified
wiper blade could result in
wiper malfunction and failure.

OED046039R

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments