manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 301 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 301

7 27

Maintenance

ENGINE COOLING SYSTEM   

The high-pressure cooling system
has a reservoir filled with year-round
antifreeze coolant. The reservoir is
filled at the factory.
Check the antifreeze protection and
coolant level at least once a year, at
the beginning of the winter season,
and before traveling to a colder cli-
mate.

Checking the coolant level     

WARNING

- Removing

radiator cap

• Never attempt to remove the

radiator cap whilst the engine
is operating or hot. Doing so
might lead to cooling system
and engine damage and could
result in serious personal
injury from escaping hot
coolant or steam.

• Turn the engine off and wait

until it cools down. Even then,
use extreme care when
removing the radiator cap.
Wrap a thick towel around it,
and turn it counterclockwise
slowly to the first stop. Step
back whilst the pressure is
released from the cooling sys-
tem. When you are sure all the
pressure has been released,
press down on the cap, using
a thick towel, and continue
turning counterclockwise to
remove it.

(Continued)

(Continued)
• Even if the engine is not oper-

ating, do not remove the radi-
ator cap or the drain plug
whilst the engine and radiator
are hot. Hot coolant and steam
may still blow out under pres-
sure, causing serious injury.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments