Kia Ceed 2006 Owner'S Manual Download Page 299

Page: 299 / 349

7 25

Maintenance

ENGINE OIL

Checking the engine oil level

1. Be sure the vehicle is on level

ground.

2. Start the engine and allow it to

reach normal operating tempera-
ture.

3. Turn the engine off and wait for a

few minutes (about 5 minutes) for
the oil to return to the oil pan.

4. Pull the dipstick out, wipe it clean,

and re-insert it fully.

5. Pull the dipstick out again and

check the level. The level should
be between F and L.

If it is near or at L, add enough oil to
bring the level to F.

Do not overfill.

Use only the specified engine oil.
(Refer to “Recommended Lubricants”
in chapter 8.)

OED076005

OED076007R

WARNING

Radiator hose

Be very careful not to touch the
radiator hose when checking or
adding the engine oil as it may
be hot enough to burn you.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Search results

Summary of Contents for Ceed 2006

Reviews:

Kia Ceed 2006, Owner'S Manual, Page: 299 / 349

Search results

Summary of Contents for Ceed 2006

Reviews: