manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 289 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 289

7 15

Maintenance

Severe driving conditions

A : Repeated short distance driving
B : Extensive idling
C : Driving in dusty, rough roads
D : Driving in areas using salt or other corrosive 

materials or in very cold weather

E : Driving in sandy areas
F : More than 50 % driving in heavy city traffic during

hot weather above 32 °C (90 °F)

G : Driving in mountainous areas.
H : Towing a trailer
I : Driving for patrol car, taxi, commercial car or vehicle

towing

J : Driving  in very cold weather
K : Driving over 170 km/h (106 mile/h)
L : Frequently driving in stop-and-go conditions

Front suspension ball joints

I

C, D, E, F, G

Disc brakes and pads, calipers and rotors

I

C, D, E, G, H

Parking brake

I

C, D, G, H

Drive shaft and boots

I

C, D, E, F, I, G, H

Climate control air filter (if equipped)

R

C, E

MAINTENANCE ITEM

Maintenance

operation

Maintenance intervals

Driving condition

Inspect more frequently 

depending on the condition

Inspect more frequently 

depending on the condition

Inspect more frequently 

depending on the condition

Inspect more frequently 

depending on the condition

Inspect more frequently 

depending on the condition

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments