manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 277 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 277

7 3

Maintenance

Scheduled maintenance serv-
ice  

Follow Normal Maintenance
Schedule if the vehicle is usually
operated where none of the following
conditions apply. If any of the following
conditions apply, follow   Maintenance
Under Severe Usage Conditions.
• Repeated short distance driving.
• Driving in dusty conditions or

sandy areas.

• Extensive use of brakes.
• Driving in areas where salt or other

corrosive materials are being used.

• Driving on rough or muddy roads.
• Driving in mountainous areas.
• Extended periods of idling or low

speed operation.

• Driving for a prolonged period in

cold temperatures and/or extreme-
ly humid climates.

• More than 50% driving in heavy

city traffic during hot weather
above 32°C (90°F).

If your vehicle is operated under the
above conditions, you should
inspect, replace or refill more fre-
quently than the following Normal
Maintenance Schedule. After 96
month or 80,000 miles (120,000 km,
Petrol Engine) / 100,000 miles
(160,000 km, Diesel Engine) contin-
ue to follow the prescribed mainte-
nance intervals.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments