manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 276 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 276

Maintenance

2

7

MAINTENANCE SERVICES

You should exercise the utmost care
to prevent damage to your vehicle
and injury to yourself whenever per-
forming any maintenance or inspec-
tion procedures.
Should you have any doubts con-
cerning the inspection or servicing of
your vehicle, we strongly recom-
mend that you have an Authorised
Kia Dealer perform this work.
An Authorised Kia Dealer has facto-
ry-trained technicians and genuine
Kia parts to service your vehicle
properly. For expert advice and qual-
ity service, see an Authorised Kia
Dealer.
Inadequate, incomplete or insuffi-
cient servicing may result in opera-
tional problems with your vehicle that
could lead to vehicle damage, an
accident, or personal injury.

Owner’s responsibility  

✽

✽

NOTICE

Maintenance Service and Record

Retention are the owner's responsi-

bility.  

You should retain documents that
show proper maintenance has been
performed on your vehicle in accor-
dance with the scheduled mainte-
nance service charts shown on the
following pages. You need this infor-
mation to establish your compliance
with the servicing and maintenance
requirements of your Kia warranties.
Detailed warranty information is pro-
vided in your Warranty & Maintenance
book.

Repairs and adjustments required as
a result of improper maintenance or
a lack of required maintenance are
not covered.
We recommend you have your vehi-
cle maintained and repaired by an
authorised Kia dealer.
An authorised Kia dealer meets Kia’s
high service quality standards and
receives technical support from Kia
in order to provide you with a high
level of service satisfaction.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments