manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 271 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 271

In case of an emergency

28

6

4. Remove the wheel lug nut wrench,

jack, jack handle, and spare tyre
from the vehicle.

5. Block both the front and rear of the

wheel that is diagonally opposite
the jack position.

6. Loosen the wheel lug nuts coun-

terclockwise one turn each, but do
not remove any nut until the tyre
has been raised off the ground.

WARNING

- Changing a

tyre

• To prevent vehicle movement

whilst changing a tyre, always
set the parking brake fully, and
always block the wheel diago-
nally opposite the wheel being
changed.

• It is recommended that the

wheels of the vehicle be
chocked, and that no person
should remain in a vehicle that
is being jacked.

OED066031R

OED066026

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments