manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 259 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 259

In case of an emergency

16

6

TOWING   

If emergency towing is necessary,
we recommend having it done by an
authorised Kia dealer or a commer-
cial tow-truck service. Proper lifting
and towing procedures are neces-
sary to prevent damage to the vehi-
cle. The use of wheel dollies or
flatbed is recommended.

For trailer towing guidelines informa-
tion, refer to section 5 “Driving Tips”.

It is acceptable to tow the vehicle
with the rear wheels on the ground
(without dollies) and the front wheels
off the ground.
When being towed by a commercial
tow truck and wheel dollies are not
used, the front of the vehicle should
always be lifted, not the rear.

OED066014

OED066013

OED066011

OED066012

CAUTION

• Do not tow the vehicle back-

wards with the front wheels on
the ground as this may cause
damage to the vehicle.

• Do not tow with sling-type

equipment. Use wheel lift or
flatbed equipment.

CAUTION

When towing the vehicle, take
care not to cause damage to the
bumper or under body of the
vehicle

CAUTION

Before towing, check the level of
the automatic transaxle fluid. If
it is below the "HOT" range on
the dipstick, add fluid. If you
cannot add fluid, a towing dolly
must be used.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments