manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 253 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 253

In case of an emergency

10

6

Inner panel fuse replacement

1. Turn the ignition switch and all

other switches off.

2. Open the fuse panel cover.

3. Pull the suspected fuse straight

out. Use the removal tool provided
in the engine compartment fuse
panel.

4. Check the removed fuse; replace it

if it is blown.

Spare fuses are provided in the
inner fuse panel (or in the engine
compartment fuse panel).

5. Push in a new fuse of the same

rating, and make sure it fits tightly
in the clips.

If it fits loosely, consult an authorised
Kia dealer.

If you do not have a spare, use a
fuse of the same rating from a circuit
you may not need for operating the
vehicle, such as the cigarette lighter
fuse.

If the headlights or other electrical
components do not work and the
fuses are OK, check the fuse block in
the engine compartment. If a fuse is
blown, it must be replaced.

OED066002R

OED066003

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments