manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 252 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 252

6 9

In case of an emergency

ELECTRICAL CIRCUIT PROTECTION 

Fuses  

A vehicle’s electrical system is pro-
tected from electrical overload dam-
age by fuses.

This vehicle has two fuse panels,
one located in the driver's side, the
other in the engine compartment.
The diesel engine has more one fuse
panel which located in the engine
compartment near the washer tank
reservior.
If any of your vehicle’s lights, acces-
sories, or controls do not work, check
the appropriate circuit fuse. If a fuse
has blown, the element inside the
fuse will be melted.
If the electrical system does not
work, first check the driver’s side
fuse panel.
Always replace a blown fuse with
one of the same rating.
If the replacement fuse blows, this
indicates an electrical problem. Avoid
using the system involved and imme-
diately consult an Authorised Kia
Dealer.

Fuse replacement     

1VQA4037

Normal

Normal

Blade type

Cartridge type

Fusible link

Blown

Blown

Normal

Blown

WARNING 

- Fuse replace-

ment

• Never replace a fuse with any-

thing but another fuse of the
same rating.

• A higher capacity fuse could

cause damage through over-
heating and possibly a fire.

• Never install a wire instead of

the proper fuse - even as a
temporary repair. It may cause
extensive wiring damage and
possibly a fire.

• Do not use a screwdriver or

any other metal object to
remove fuses because it may
cause a short circuit and dam-
age the system.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments