manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 228 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 228

5 13

Driving tips

Chain installation 

When installing chains, follow the
manufacturer's instructions and
mount them as tightly as you can.
Drive slowly with chains installed. If
you hear the chains contacting the
body or chassis, stop and tighten
them. If they still make contact, slow
down until it stops. Remove the
chains as soon as you begin driving
on cleared roads.

WARNING 

- Mounting

chains

When mounting snow chains,
park the vehicle on level ground
away from traffic. Turn on the
vehicle Hazard Warning flashers
and place a triangular emer-
gency warning device behind
the vehicle if available. Always
place the vehicle in park (P),
apply the parking brake and
turn off the engine before
installing snow chains.

WARNING

- Tyre  chains

• The use of chains may

adversely affect vehicle han-
dling.

• Do not exceed 30 km/h (20

mph) or the chain manufactur-
er’s recommended speed
limit, whichever is lower.

• Drive carefully and avoid

bumps, holes, sharp turns,
and other road hazards, which
may cause the vehicle to
bounce.

• Avoid sharp turns or locked-

wheel braking.

CAUTION

• Chains that are the wrong size

or improperly installed can
damage your vehicle's brake
lines, suspension, body and
wheels.

• Stop driving and retighten the

chains any time you hear them
hitting the vehicle.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments