manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 211 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 211

4 83

Driving your vehicle

Checking the amount of air
conditioner refrigerant and
compressor lubricant

When the amount of refrigerant is
low, the performance of the air con-
ditioning is reduced. Overfilling also
has a bad influence on the air condi-
tioning system.
Therefore, if abnormal operation is
found, have the system inspected by
an authorised Kia dealer.

✽

✽

NOTICE

When the performance of the air

conditioning system is reduced it is

important that the correct type and

amount of oil and refrigerant is

used. Otherwise, damage to the

compressor and abnormal system

operation  may occur. 

WARNING 

The air conditioning system
should be serviced by an autho-
rised Kia dealer. Improper serv-
ice may cause serious injury.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments