manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 199 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 199

4 71

Driving your vehicle

✽

✽

NOTICE

• When using the air conditioning

system, monitor the temperature

gauge closely whilst driving up

hills or in heavy traffic when out-

side temperatures are high. Air

conditioning  system operation

may cause engine overheating.

Continue to use the blower fan but

turn the air conditioning system

off if the temperature gauge indi-

cates engine overheating.

• When opening the windows in

humid weather air conditioning

may create water droplets inside

the vehicle. Since excessive water

droplets may cause damage to

electrical equipment, air condi-

tioning should only be run with

the windows closed.

Air conditioning system oper-
ation tips  

• If the vehicle has been parked in

direct sunlight during hot weather,
open the windows for a short time
to let the hot air inside the vehicle
escape.

• To help reduce moisture inside of

windows on rainy humid days,
decrease the humidity inside the
vehicle by operating the air condi-
tioning system.

• During air conditioning system

operation, you may occasionally
notice a slight change in engine
speed at idle as the air condition-
ing  compressor cycles on. This is
a normal system operation charac-
teristics.

• Use the air conditioning system

every month if only for a few min-
utes to ensure maximum system
performance.

• When using the air conditioning

system, you may notice clear water
dripping (or even pudding) on the
ground  under the passenger side
of the vehicle. This is a normal sys-
tem operation characteristics.

• Operating the air conditioning sys-

tem in the recirculated air position
does provide maximum cooling,
however, continual operation in this
mode may cause the air inside the
vehicle to become stale.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments