manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 193 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 193

4 65

Driving your vehicle

Fan speed control knob  

The ignition switch must be in the ON
position for fan operation.
The fan speed control knob allows
you to control the fan speed of the air
flowing from the ventilation system.
To change the fan speed, turn the
knob to the right for higher speed or
left for lower speed.
Setting the fan speed control knob to
the “OFF” position turns off the fan.

Temperature control knob

The temperature control knob allows
you to control the temperature of the
air flowing from the ventilation sys-
tem. To change the air temperature in
the passenger compartment turn the
knob to the right for warm and hot air
or left for cooler air.

Mode selection knob  

The mode selection knob controls
the direction of the air flow through
the ventilation system.

OED046047

OED046048

OED046049

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments