manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 191 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 191

4 63

Driving your vehicle

Front windscreen deicer 
(if equipped)

The engine must be running to
enable this feature. To activate the
front windscreen deicer, press the
front windscreen deicer button. The
indicator on the button illuminates
when the deicer is ON. The front
windscreen deicer automatically
turns off after 20 minutes or when
the ignition switch is turned off. To
turn off the deicer, press the front
windscreen deicer button again.

The hazard warning flasher should
be used whenever you find it neces-
sary to stop the car in a hazardous
location. When you must make such
an emergency stop, always pull off
the road as far as possible.
The hazard warning lights are turned
on by pushing in the hazard switch.
This causes all turn signal lights to
blink. The hazard warning lights will
operate even though the key is not in
the ignition switch.
To turn the hazard warning lights off,
push the switch a second time.

OED046045R

OED046042R

HAZARD WARNING FLASHER 

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments