manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 190 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 190

Driving your vehicle

62

4

✽

✽

NOTICE

If you want to defrost and defog on

the front windscreen, refer to

“Windscreen Defrosting and

Defogging” in this section.  

Rear window defroster

The defroster heats the window to
remove frost, fog and thin ice from
the interior and exterior of the rear
window, whilst engine is running.

To activate the rear window
defroster, press the rear window
defroster button. The indicator on the
rear window defroster button illumi-
nates when the defroster is ON.
If there is heavy accumulation of
snow on the rear window, brush it off
before operating the rear defroster.
The rear window defroster automati-
cally turns off after approximately 20
minutes or when the ignition switch is
turned off. To turn off the defroster,
press the rear window defroster but-
ton again.

Outside mirror defroster 
(if equipped)

If your vehicle is equipped with out-
side mirror defrosters, they will oper-
ate at the same time when you turn
on the rear window defroster.

DEFROSTER    

OED046043

OED046044

Type A

Type B

CAUTION

To prevent damage to the con-
ductors bonded to the inside
surface of the rear window,
never use sharp instruments or
window cleaners containing
abrasives to clean the window.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments