manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 178 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 178

Driving your vehicle

50

4

The back warning system assists the
driver during backward movement of
the vehicle by chiming if any object is
sensed within a distance of 120 cm
(47 in.) behind the vehicle. This sys-
tem is a supplemental system and it
is not intended to nor does it replace
the need for extreme care and atten-
tion of the driver. The sensing range
and objects detectable by the back
sensors are limited. Whenever back-
ing-up, pay as much attention to
what is behind you as you would in a
vehicle without a back warning sys-
tem.

Operation of the back warning
system

Operating condition

• This system will activate when back-

ing up with the ignition switch ON.
If the vehicle is moving at a speed
over  5 km/h (3 mph), the system
may not be activated correctly.

• The sensing distance whilst the

Back Warning System is in opera-
tion is approximately 120 cm (47
in.).

• When more than two objects are

sensed at the same time, the clos-
est one will be recognized first.

Types of warning sound

• When an object is 120 cm to 81 cm

(47 in. to 32 in.) from the rear
bumper: Buzzer beeps intermit-
tently

• When an object is 80 cm to 41 cm

(31 in. to 16 in.) from the rear
bumper: Buzzer  beeps more fre-
quently

• When an object is within 40 cm (15

in.) of the rear bumper:
Buzzer sounds continuously.

BACK WARNING SYSTEM (IF EQUIPPED)

OED046092

WARNING 

The Back Warning System is a
supplementary function only.
The operation of the Back
Warning System can be affected
by several factors (including
environmental conditions). It is
the responsibility of the driver
to always check the area behind
the vehicle before and whilst
backing up.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments