manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 164 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 164

Driving your vehicle

36

4

CAUTION

If the engine is not stopped
immediately, severe damage
could result.

Engine oil pressure
warning  

This warning light indicates the
engine oil pressure is low.
If the warning light illuminates whilst
driving:
1. Drive safely to the side of the road

and stop.

2. With the engine off, check the

engine oil level. If the level is low,
add oil as required.

If the warning light remains on after
adding oil or if oil is not available, call
an Authorised Kia Dealer.

Charging system 
warning  

This warning light indicates a mal-
function of either the generator or
electrical charging system.
If the warning light comes on whilst
the vehicle is in motion:
1. Drive to the nearest safe location.
2. With the engine off, check the gen-

erator drive belt for looseness or
breakage.

3. If the belt is adjusted properly, a

problem exists somewhere in the
electrical charging system. Have
an Authorised Kia Dealer correct
the problem as soon as possible.

Seat belt warning  

As a reminder to the driver and pas-
senger, seat belt warning light will
blink or illuminate for approximately 6
seconds each time you turn the igni-
tion switch ON.
For details, refer to the seat belt on
chapter 3.

Shift pattern indicators
(if equipped)

The individual indicators illuminate to
show the automatic transaxle shift
lever selection.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments