manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 149 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 149

4 21

Driving your vehicle

✽

✽

NOTICE

When you jump start your vehicle

because of a drained battery, the

engine may not run as smoothly and

the ABS warning light may turn on

at the same time. This happens

because of the low battery voltage. It

does not mean your ABS is malfunc-

tioning.

• Do not pump your brakes!

• Have the battery recharged before

driving the vehicle.

ABS

W-78

CAUTION

• If the ABS warning light is on

and stays on, you may have a
problem with the ABS system.
In this case, however, your reg-
ular brakes will work normally.

• The ABS warning light will stay

on for approximately 3 sec-
onds after the ignition switch
is ON. During that time, the
ABS will go through self-diag-
nosis and the light will go off if
everything is normal. If the
light stays on, you may have a
problem with your ABS sys-
tem. Contact an authorised Kia
dealer as soon as possible.

CAUTION

• When you drive on a road hav-

ing poor traction, such as an
icy road, and operate your
brakes continuously, the ABS
will be active continuously
and the ABS warning light
may illuminate. Pull your car
over to a safe place and stop
the engine.

• Restart the engine. If the ABS

warning light is off, then your
ABS system is normal.
Otherwise, you may have a
problem with the ABS.
Contact an authorised Kia
dealer  as soon as possible.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments