manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 134 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 134

Driving your vehicle

6

4

Starting the diesel engine

To start the diesel engine when the
engine is cold, it has to be pre-heat-
ed before starting the engine and
then has to be warmed up before
starting to drive.
1. Make sure the parking  brake is

applied.

2.

Manual Transaxle

- Depress the

clutch pedal  fully and shift the
Transaxle into the Neutral. Keep
the clutch pedal depressed whilst
cranking the engine.

Automatic Transaxle

- Place the

Transaxle shift lever in P(park).
Depress the brake pedal fully.

You can also start the engine when
the shift lever is in the N(neutral)
position.

3. Turn the ignition switch ON posi-

tion to pre-heat the engine. Then
the glow indicator light will illumi-
nate.

4. If the glow indicator light goes out,

turn the ignition switch to START
and hold it there until the engine
starts (a maximum of 10 sec-
onds), then release the key.

✽

✽  

NOTICE

If the engine were not started within

2 seconds after the preheating is com-

pleted, turn the ignition key once

more to the LOCK position during

10 seconds, and then to the ON posi-

tion, in order to preheat again.  

Starting and stopping the
engine for turbocharger 
intercooler 

1. Do not race or accelerate the

engine immediately after starting.

If the engine is cold, idle for sever-
al seconds before sufficient lubri-
cation is ensured in the tur-
bocharger unit.

2. After high speed or extended driv-

ing, requiring a heavy engine load,
idle the engine about 1 minute
before turning it off.

This idle time will allow the tur-

bocharger to cool prior to shutting
the engine off.

W-60

Glow indicator light

CAUTION

Do not turn the engine off imme-
diately after it has been subject-
ed to a heavy load. Doing so
may cause severe damage to
the engine or turbocharger unit.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments