Kia Ceed 2006 Owner'S Manual Download Page 111

Page: 111 / 349

3 101

Knowing your vehicle

General information

Notes on operating instructions

The following reading aids are used
to simplify these operating instruc-
tions:

)

asks you to perform an action

shows the unit’s reaction

✐

provides extra info

identifies a list

AUDIO SYSTEM

WARNING

A WARNING indicates a situa-
tion in which harm, serious bod-
ily injury or death could result if
the warning is ignored.

CAUTION

A CAUTION indicates a situation
in which damage to your vehicle
could result if the caution is
ignored.

CLASS 1

LASER PRODUCT

Class 1 laser product

CAUTION

Any inappropriate use of the
device may expose the user to
invisible laser rays which
exceed the limits for Class 1
laser products.

WARNING

Don’t use a cellular phone when
you are driving. You must stop
at a safe place to use a celluar
phone.

WARNING

When driving your vehicle, be
sure to keep the volume of the
unit set low enough to allow you
to hear sounds coming from the
outside.

CAUTION

• Do not place beverages close

to the audio system. The audio
system mechanism may be
damaged if you spill them.

• Do not strike or allow anything

to impact the audio system,
damage to the system mecha-
nisms could occur.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Search results

Summary of Contents for Ceed 2006

Reviews:

Kia Ceed 2006, Owner'S Manual, Page: 111 / 349

Search results

Summary of Contents for Ceed 2006

Reviews: