manualshive.com logo in svg

Kia Ceed 2006, Owner'S Manual, Page: 103 / 349

Share
Download
Kia Ceed 2006 Owner'S Manual Download Page 103

3 93

Knowing your vehicle

If your vehicle is equipped with a
sunroof, you can slide or tilt your
sunroof with the sunroof control but-
tons located on the overhead con-
sole.
(1) Slide button
(2) Tilt button
(3) Close button

The sunroof can only be opened,
closed, or tilted when the ignition
switch is in the ON position.

✽

✽

NOTICE

• In cold and wet climates, the sun-

roof may not work properly due to

freezing conditions.

• After washing the car or after

there is rain, be sure to wipe off

any water that is on the sunroof

before operating it.

✽

✽

NOTICE

The sunroof cannot slide when it is

in the tilt position nor can it be tilted

whilst in an open or slide position. 

SUNROOF (IF EQUIPPED)

OED036064

CAUTION

Do not continue to press the
sunroof control button(s) after
the sunroof is in the fully open,
closed,

or tilt position(s).

Damage to the motor or system
components could occur.

WARNING

Never adjust the sunshade
whilst driving. This could result
in loss of control and an acci-
dent that may cause death, seri-
ous injury, or property damage.

Summary of Contents for Ceed 2006






























































































































































































































































































































































Reviews:

No comments