manualshive.com logo in svg

Kia Carnival 2023, Owner'S Manual, Page: 58 / 606

Share
Download
Kia Carnival 2023 Owner'S Manual Download Page 58

37

3

3

Safety features of your vehicle

Seat belts

The purpose of the pre-tensioner is to 
make sure that the seat belts fit tightly 
against the occupant's body in certain 
collisions.
The pre-tensioner seat belts may be 
activated in crashes where the collision 
is severe enough.
When the vehicle stops suddenly, or if 
the occupant tries to lean forward too 
quickly, the seat belt retractor will lock 
into position. In certain frontal collisions, 
the pre-tensioner will activate and pull 
the seat belt into tighter contact against 
the occupant's body.
If the system senses excessive tension 
on the driver or passenger's seat belt 
when the pre-tensioner system acti

-

vates, the load limiter inside the retractor 
pre-tensioner will release some of the 
pressure on the affected seat belt.

WARNING

For your safety, be sure that the belt 
webbing is not loose or twisted and 
always sit properly on your seat.

NOTICE

The pre-tensioner may activate not only 
in a frontal collision but also in a side col

-

lision, if the vehicle is equipped with a 
side or curtain air bag.

The seat belt pre-tensioner system con

-

sists mainly of the following compo

-

nents. Their locations are shown in the 
illustration:

1. Supplemental Restraint System (SRS) 

air bag warning light

2. Front retractor pre-tensioner assem

-

bly

3. SRS control module

WARNING

Skin irritation

Wash all exposed skin areas thoroughly 
after an accident in which the pre-ten

-

sioner seat belts were activated. The fine 
dust from the pre-tensioner activation 
may cause skin irritation and should not 
be inhaled for prolonged periods.

NOTICE

僅 Both the driver's and front passen

-

ger's seat belt pre-tensioner systems 
may be activated not only in certain 
frontal collisions, but also in certain 
side collisions or rollovers, if the vehi

-

cle is equipped with a side or curtain 
air bag.

僅 Because the sensor that activates the 

SRS air bag is connected with the pre-
tensioner seat belt, the SRS air bag 

warning light 

 on the instrument 

panel will appear for approximately 3 
~ 6 seconds after the ignition switch 
or ENGINE START/STOP button has 

OON039121NR

Summary of Contents for Carnival 2023































































































































































































































































































































































































































































































































































































































Reviews:

No comments