manualshive.com logo in svg

Kia Carnival 2023, Owner'S Manual, Page: 574 / 606

Share
Download
Kia Carnival 2023 Owner'S Manual Download Page 574

73

7

7

Maintenance

Emission control system

lethal if inhaled. Follow the instructions 
on this page to avoid CO poisoning.

僅 Do not operate the engine in confined 

or closed areas (such as garages) any 
more than what is necessary to move 
the vehicle in or out of the area.

僅 When the vehicle is stopped in an 

open area for more than a short time 
with the engine running, adjust the 
ventilation system (as needed) to 
draw outside air into the vehicle.

僅 Never sit in a parked or stopped vehi

-

cle for any extended time with the 
engine running.

僅 When the engine stalls or fails to start, 

excessive attempts to restart the 
engine may cause damage to the 
emission control system.

Operating precautions for cata

-

lytic converters

WARNING

Catalytic converter

Keep away from the catalytic converter 
and exhaust system while the vehicle is 
running or immediately thereafter. The 
exhaust and catalytic systems are very 
hot and may burn you.

WARNING

Fire

僅 Do not park, idle or drive the vehicle 

over or near flammable objects, such 
as grass, vegetation, paper, leaves, 
etc. A hot exhaust system can ignite 
flammable items under your vehicle.

僅 Also, do not remove the heat sink 

around the exhaust system, do not 
seal the bottom of the vehicle or do 
not coat the vehicle for corrosion con

-

trol. It may present a fire risk under 
certain conditions.

Your vehicle is equipped with a catalytic 
converter emission control device.
Therefore, the following precautions 
must be observed:
僅 Use only UNLEADED FUEL for gaso

-

line engines.

僅 Do not operate the vehicle when there 

are signs of engine malfunction, such 
as misfire or a noticeable loss of per

-

formance.

僅 Do not misuse or abuse the engine. 

Examples of misuse are coasting with 
the ignition off and descending steep 
grades in gear with the ignition off.

僅 Do not operate the engine at high idle 

speed for extended periods (5 min

-

utes or more).

僅 Do not modify or tamper with any 

part of the engine or emission control 
system. All inspections and adjust

-

ments must be made by an autho

-

rized Kia dealer.

僅 Avoid driving with an extremely low 

fuel level. Running out of fuel could 
cause the engine to misfire, damaging 
the catalytic converter.

Failure to observe these precautions 
could result in damage to the catalytic 
converter and to your vehicle. Addition

-

ally, such actions could void your war

-

ranties.

Summary of Contents for Carnival 2023































































































































































































































































































































































































































































































































































































































Reviews:

No comments