manualshive.com logo in svg

Kia Carnival 2023, Owner'S Manual, Page: 529 / 606

Share
Download
Kia Carnival 2023 Owner'S Manual Download Page 529

Maintenance

28

7

Wiper blades

Rear wiper blade replacement

1. Within 20 seconds after the vehicle 

ignition is OFF, move the wiper lever 
to MIST position for over 2 seconds 
until the wiper moves down to the 
bottom middle part.

2. Raise the wiper arm and pull out the 

wiper blade assembly.

3. Lift up the wiper blade, and pull the 

blade to remove it.

4. Install the new blade assembly by 

inserting the center part into the slot 
in the wiper arm until it clicks into 
place.

5. Make sure the blade assembly is 

installed firmly by trying to pull it 
slightly.
If the replacement is complete, put 
down the wiper arm to place it on the 
rear windshield, and turn the vehicle 
ignition to ON and operate the wipers 
to check the blade is installed cor

-

rectly.

To prevent damage to the wiper arms or 
other components, have the wiper blade 
replaced by a professional workshop. 
Contact and visit an authorized Kia 
dealer.

OKA4070012N

OKA4070013

OMQ4070104L

OMQ4070094L

Summary of Contents for Carnival 2023































































































































































































































































































































































































































































































































































































































Reviews:

No comments