Kia Carnival 2023 Owner'S Manual Download Page 522

Page: 522 / 606

Maintenance

Washer fluid

Checking the washer fluid level

The reservoir is translucent so that you
can check the level with a quick visual
inspection.

僅 Check the fluid level in the washer

fluid reservoir and add fluid if neces

sary. Plain water may be used if
washer fluid is not available.
However, use washer solvent with
antifreeze characteristics in cold cli

mates to prevent freezing.

WARNING

Washer fluid

僅 Do not use radiator coolant or anti

freeze in the washer fluid reservoir.

僅 Radiator coolant can severely obscure

visibility when sprayed on the wind

shield and may cause loss of vehicle
control or damage to paint and body
trim.

僅 Windshield Washer fluid agents con

tain some amounts of alcohol and can
be flammable under certain circum

stances. Do not allow sparks or flame
to contact the washer fluid or the
washer fluid reservoir. Damage to the
vehicle or occupants could occur.

僅 Windshield washer fluid is poisonous

to humans and animals. Do not drink
and avoid contacting windshield
washer fluid. Serious injury or death
could occur.

OKA4070005

Summary of Contents for Carnival 2023































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Carnival 2023

Reviews:

Kia Carnival 2023, Owner'S Manual, Page: 522 / 606

Search results

Summary of Contents for Carnival 2023

Reviews: