Kia Carnival 2023 Owner'S Manual Download Page 448

Page: 448 / 606

173

Driving your vehicle

Remote Smart Parking Assist (RSPA)

The function will cancel in the fol

lowing conditions when:

僅 The steering wheel is steered
僅 The gear is shifted while the vehicle is

moving

僅 Operating EPB while the vehicle is

moving

僅 The engine hood is open
僅 Vehicle speed is above 3 mph (5 km/

僅 Rapid acceleration occurs
僅 Vehicle skid occurs
僅 The wheel is stuck by an obstacle and

cannot move

僅 There are pedestrians, animals or

objects at the front and rear of the
vehicle at the same time

僅 Approximately 3 minutes and 50 sec

onds have past after Remote Opera

tion function has started to operate

僅 The slope of the road exceeds the

operational range

僅 The steering wheel, gearshift, braking,

and drive controls are not working
normally

僅 The function is paused for more than

1 minute

僅 The total travel distance of the vehicle

has exceeded 45 ft. (14 m) after
Remote Operation function operation

僅 There is a problem with the smart key

or the smart key battery is low

僅 ABS, TCS or ESC operates due to slip

pery road conditions

僅 The brake pedal or accelerator pedal

is depressed when all the doors are
closed

僅 The smart key is outside the vehicle

when the brake pedal is depressed
while the driver's door is open.

僅 The alarm of the Theft Alarm System

sounds

When Remote Operation function is can

celed, the vehicle will automatically stop,
shift the gear to P (Park) and engage
EPB (Electronic Parking Brake).

CAUTION

Check whether the doors are locked
when Remote Operation function is can

celed.

Summary of Contents for Carnival 2023































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Carnival 2023

Reviews:

Kia Carnival 2023, Owner'S Manual, Page: 448 / 606

Search results

Summary of Contents for Carnival 2023

Reviews: