Kia Carnival 2023 Owner'S Manual Download Page 420

Page: 420 / 606

145

Driving your vehicle

Rear Cross-Traffic Collision-Avoidance Assist (RCCA)

Monitor is operating, a warning will
also appear on the infotainment sys

tem screen.

僅 The function will operate when all the

following conditions are satisfied:
- The gear is shifted to R (Reverse)
- Vehicle speed is below 5 mph (8

km/h)

- The approaching vehicle is within

approximately 5 ft. (1.5 m) from the
left and right side of your vehicle

- The speed of the vehicle approach

ing from the left and right is above
3 mph (5 km/h)

僅 Emergency braking will be assisted to

help prevent collision with approach

ing vehicles from the left and right.

NOTICE

Brake control will end when:
僅 The approaching vehicle is out of the

detecting range

僅 The approaching vehicle passes

behind your vehicle

僅 The approaching vehicle does not

drive toward your vehicle

僅 The approaching vehicle speed slows

down

僅 The driver depresses the brake pedal

with sufficient power

Stopping vehicle and ending
brake control

僅 When the vehicle is stopped due to

emergency braking, the 'Drive care

fully' warning message will appear on
the cluster.

僅 For your safety, the driver should

depress the brake pedal immediately
and check the surroundings.

僅 Brake control will end after the vehicle

is stopped by emergency braking for
approximately 2 seconds.

僅 During emergency braking, braking

control by the function will automati

cally cancel when the driver exces

sively depresses the brake pedal.

WARNING

Take the following precautions when
using Rear Cross-Traffic Collision-Avoid

ance Assist:
僅 For your safety, change the Settings

after parking the vehicle at a safe
location.

僅 If any other function's warning mes

sage is displayed or audible warning
is generated, Rear Cross-Traffic Colli

sion-Avoidance Assist warning mes

sage may not be displayed and
audible warning may not be gener

ated.

OKA4050123L

Summary of Contents for Carnival 2023































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Carnival 2023

Reviews:

Kia Carnival 2023, Owner'S Manual, Page: 420 / 606

Search results

Summary of Contents for Carnival 2023

Reviews: