manualshive.com logo in svg

Kia Carnival 2023, Owner'S Manual, Page: 40 / 606

Share
Download
Kia Carnival 2023 Owner'S Manual Download Page 40

19

3

3

Safety features of your vehicle

Seat

Removing the seat (2nd row seat)

1. Insert the seat belt buckle in the 

pocket between the rear seatback 
and cushion.

2. Lower the headrest to the lowest posi

-

tion.

3. Slide the seat to the farthest forward.
4. Fold the seat back by pulling up the 

reclining lever or strap.

5. Pull the removal lever or strap and lift 

the rear portion of the seat cushion.

2nd row outboard seat

2nd row center seat

6. Remove the entire seat from the floor.

Installing the seat (2nd row seat)

1. Put the front hook (1) on the front 

install guide (A) that inside rail on the 
floor.

OKA4030120L

OKA4030123N

OKA4030124N

OKA4030147N

OKA4040548N

Summary of Contents for Carnival 2023































































































































































































































































































































































































































































































































































































































Reviews:

No comments