manualshive.com logo in svg

Kia Carnival 2023, Owner'S Manual, Page: 216 / 606

Share
Download
Kia Carnival 2023 Owner'S Manual Download Page 216

121

4

4

Features of your vehicle

Wipers and washers

and always check the road conditions 
for your safety.

僅 When High Beam Assist does not 

operate normally, change the head

-

lamp position manually between high 
beam and low beam.

Wipers and washers

The wipers and washers remove foreign 
substances from the windshield and rear 
window, helping to maintain visibility.

A: Wiper speed control

僅 MIST – Single wipe
僅 OFF – Off
僅 INT – Intermittent wipe

AUTO*: - Auto control wipe

僅 LO – Low wiper speed
僅 HI – High wiper speed

B: Intermittent control wipe time 
adjustment
C: Wash with brief wipes (Pull lever 
towards you)
D: Rear wiper/washer control

僅 HI - Continuous wipe
僅 LO - Intermittent wipe

OMQ4040061

OMQ4040062

Summary of Contents for Carnival 2023































































































































































































































































































































































































































































































































































































































Reviews:

No comments