manualshive.com logo in svg

Kia Carnival 2023, Owner'S Manual, Page: 160 / 606

Share
Download
Kia Carnival 2023 Owner'S Manual Download Page 160

65

4

4

Features of your vehicle

Dual sunroof

Resetting the sunroof

Front seat sunroof

Rear seat sunroof

In some circumstances resetting the 
sunroof operation may need to be per

-

formed. Some instances where resetting 
the sunroof may be required include:
僅 When the 12-volt battery is either dis

-

connected or discharged

僅 When the sunroof fuse is replaced
僅 If the sunroof one-touch AUTO OPEN/

CLOSE operation is not functioning 
properly

Sunroof resetting procedure:

1. It is recommended to perform the 

reset procedure with the vehicle 
engine running. Start the vehicle in P 
(Park).

2. Make sure the sunroof glass is in the 

fully closed position. If the sunroof 
glass is open, push the switch forward 
until the sunroof glass is fully closed.

3. Release the switch when the sunroof 

glass is fully closed.

4. Push the switch forward until the sun

-

roof glass moves slightly. Then 
release the switch.

5. Once again push and hold the sun

-

roof switch forward until the sunroof 
glass slides open and close. Do not 
release the switch until the operation 
is completed.
If you release the switch during oper

-

ation, start the procedure again from 
step 2.

NOTICE

If the sunroof does not reset when the 
vehicle battery is disconnected or dis

-

charged, or the sunroof fuse is blown, 
the sunroof may not operate normally.

Sunroof open warning

OKA4041525

OKA4041526

OKA4040107

Summary of Contents for Carnival 2023































































































































































































































































































































































































































































































































































































































Reviews:

No comments