KFI U45-R2 Operator'S Manual Download | Manualshive

Page: 1 / 24

background image

OPERA

TOR

’S MANUAL

SERIAL NO. LABEL

or visit

www.kfiproducts.com

READ AND SAVE THIS MANUAL.

This  manual  contains  important  safety
precautions  which  should  be  read  and
understood before operating the product.
Failure  to  do  so  could  result  in  serious
injury. This manual should remain with the

product. Specifications, descriptions, and illustrations
in this manual are as accurate as known at the time of
publication, but are subject to change without notice.

KFI Products - Kappers Fabricating, Inc., Spring Valley, MN USA

Place serial label

here for reference.

Support:

MODEL

#U45-R2

4,500 LB. (2041 KG)

Made in China - REV 20220725

ATV WINCH

STEEL CABLE

1
2
3
...
»

Summary of Contents for U45-R2

























Reviews:

No comments

Related manuals for U45-R2

Brand: Ingersoll-Rand Pages: 36

Brand: Ramsey Winch Pages: 80

Brand: Prowinch Pages: 22

Brand: Black Widow Pages: 17

Brand: Westfalia Pages: 23

Brand: Ronstan Pages: 8

Andersen 18ST FS

Brand: Ronstan Pages: 8

Brand: Ronstan Pages: 8

Andersen Compact Motor 52ST

Brand: Ronstan Pages: 22

Brand: SuperATV Pages: 16

OZWINCH OMW-SS316-1000

Brand: HES Pages: 12

Brand: Ingersoll-Rand Pages: 16

TANGO KE 300/500

Brand: haacon Pages: 16

Best Hoist 60138

Brand: Tuff-Built Pages: 22

Brand: Superwinch Pages: 17

Brand: JSP Pages: 43

Brand: Hamron Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands